Skip to Content

How To Clean Car Wax Applicator Pads

Keeping car wax applicator pads clean extends their life, ensuring they are in good condition every time you use them. However, it can be hard to remove the wax from the pad, and leaving the pad for long without cleaning it hardens the wax, making it sticky. If you do not know how to clean your applicator pads, you have come to the right place.

Hand applying car wax

Here are 8 tips on how to clean your car wax applicator pads:

  1. Stop using pads once they are saturated with wax.
  2. Wipe off dirt using the electric polisher and a towel.
  3. Remove excess wax with an all-purpose cleaner.
  4. Soak the car wax applicator pads.
  5. Rinse the applicator pads in warm water.
  6. Clean the pads using a detergent.
  7. Rinse the applicator pads to remove the detergent.
  8. Dry the pads to squeeze water.

By reviewing this article, you will learn the best way to clean your car wax applicator pads to ensure they last for a long time. If you keep buying new applicator pads, these tips will come in handy.

1. Stop Using Pads Once They Are Saturated With Wax

Hand holding pads while applying wax on it

After using the car wax applicator pad for one hour, you will notice that the results are different from when you first started waxing the car. The pad will have absorbed all the wax and be completely saturated. It will not only lose its corrective ability, but you will notice splatters coming out of the pad.

At this point, you should stop using the pad because it needs cleaning.

However, if you cannot tell whether the pad is saturated, the rule of thumb is to clean the pad after waxing two sections of the car. It would be best to use the trunk lid to estimate each section.

2. Wipe Off Dirt Using the Electric Polisher and a Towel

Hand wiping off dirt

Your electric polisher will come in handy when cleaning your applicator pad. Place the pad on the electric polisher and flip it to ensure the pad is facing up. Hold a towel against the pad and turn on the electric polisher. Gently wipe the pad while it spins to remove all the dirt.

Additionally, you can use a brush, but you should not use a lot of pressure when brushing the pad to avoid damaging it.

Ultimately, ensure you move the towel or the brush to the different pad areas to cover all areas. For instance, you can start cleaning the pad’s outer rim and then move to the center.

Continue this process for a few minutes or until you notice the pad changing back to its original color.

3. Remove Excess Wax With an All-Purpose Cleaner

An all-purpose cleanser and a pad

The applicator pad may contain excess wax, especially if you have used it for a while. Thus, you will need an all-purpose cleaner to remove some of the wax. Using a cleaner will make it much easier to clear the wax from the pad.

You can use the GP66 Green Miracle Cleaner to remove the excess was. The liquid-based cleaner removes grime and grease stains without bleaching your applicator pads.

For this cleaning tip, you simply have to hold your applicator pad with one hand and spray it with the all-purpose cleaner.

If you get distracted in the middle of cleaning an applicator pad, ensure that you seal the pad in a zip-top bag before you continue cleaning. This prevents the wax from drying inside the pad, making it much easier to remove later on.

4. Soak the Car Wax Applicator Pads

Car wax applicator soak in detergent

The primary aim of soaking the car wax applicator pads in a bucket with cold water is to loosen up the wax to make the cleaning easier. The bucket must contain a detergent before soaking.

For those at home, you can use a dishwashing liquid as the detergent. However, you must thoroughly mix it with water to ensure optimal results.

Additionally, ensure the pad is placed face down in the water when soaking.

For the dishwashing liquid, consider Frosch Dishwashing Gel. This detergent cuts through grease and grime, making it ideal for cleaning your pads.

5. Rinse the Applicator Pads in Warm Water

Rinse the applicator pads with warm water

After the pads have been soaked for a while, they may be fairly easy to clean. However, the main thing that you should be worried about is the wax glued to the pads.

As such, you should rinse the pads in warm water and not boiling water. The shortcomings of rinsing the pad in boiling water are that it may soften the Velcro backing glue, and you run the risk of burning yourself.

CarCareReport dot com is owner of this article and was first posted on Sep 14, 2022 and was updated on ..

The warm water will expand the pad, making it pliable. Massage the pad while the warm water is running without using a detergent, and you will notice the wax coming out.

You will not remove all the wax, but the applicator pad’s cells will open. At this point, the pad is ready for a thorough cleaning.

6. Clean the Pads Using a Detergent

Detergetn, gloves , and an applicator

At this point, it will be easy for you to clean the pads because some of the wax has been removed. You should spray the detergent on the pad and massage it softly for a few minutes.

Keep massaging the pad until you notice that all the wax has come out.

You can use Adam’s Car Wash Shampoo for the detergent. This liquid-based detergent is particularly handy because it can also clean other tools that you may use to clean your car. It also uses a neutral pH formula, so it won’t damage your car’s finish if you use it frequently.

First published on Sep 14, 2022 by CarCareReport.com.

7. Rinse the Applicator Pads To Remove the Detergent

Rinsing the applicator pads to remove the detergent

Rinsing the applicator pads removes the detergent and the unwanted particles in the pad. Open your faucet and ensure the water running is of a lukewarm temperature. Massage the applicator pad under the lukewarm water, but add some detergent if you still notice some wax.

Rinse the applicator pad until the water is clear.

8. Dry the Pads To Squeeze Water

Squeezing the pads to dry

The pads will be soaking wet after rinsing, and they may take a while to dry. You can use two methods to speed up the drying process.

  • Method 1: Fold a piece of cardboard in half and put the pad between the cardboard to squeeze out the water.
  • Method 2: Use two flat objects, place the pad between the two objects, and squeeze the water out of the pad.

You can also squeeze the pad using your hands. However, doing so can stretch it, making it unbalanced and difficult to use in the future.

Key Takeaways

The best way to maintain your car wax applicator pad is to ensure it is clean. This saves you the expense of buying these pads whenever you are waxing your car.

You can utilize a few cleaning tips to increase your applicator pad’s longevity:

  • Clean the pads after they are saturated
  • Rinse the pads in warm water
  • Use detergents to clean the pads
  • Dry the pads correctly

Related Articles

Can You Wax a Car Without Washing It First?

How to Tell When the Car Wax is Dry

Can You Still Buff a Car in the Rain?

How Long Should Paint Cure Before Polishing?

CarCareReport dot com first published this article on Sep 14, 2022..

Can You Apply Clear Coat After Wet Sanding a Car?